Top 10 common forklift crashes ， forklift operation must pay attention to these issues ！.

Top 10 common forklift crashes ， forklift operation must pay attention to these issues ！.

Blog Article

Do not underestimate the forklift at the workplace. If the operation is bad, there will be significant mishaps in mins, and there are lots of mishaps entailing forklifts.

Case 1: The forklift freight blocked the vehicle driver's sight, and the individual ahead might not be found, resulting in a rolling crash.
Situation 2: In order to maintain the balance of the forklift when lifting heavy products, the employees utilized their body weight as the weight, which nearly triggered casualties.
Case 3: The size of the forklift cargo exceeds the allowable width of the path and holds on the roadside rack, which almost causes an accident.
Situation 4: Forklift is speeding up and surrender during a turn.
Situation 5: The forklift chauffeur did not observe the pedestrian, and the pedestrian did not observe the forklift.
Instance 6: The forklift raises the workers illegally, the forklift vehicle driver does not wear the safety belt, the forklift lifter falls and the vehicle driver is squashed when the forklift rolls over.
Case 7: The forklift driver did not use a seat belt and fell from the vehicle when it rolled over and was squashed.
Forklift operation should take notice of these issues ：.

Begin.
1. Prior to starting, observe the environments, and after confirming that there are no obstacles that prevent the safety and security of driving, honk the horn first and afterwards begin.
2. For vehicles with hydraulic (air pressure) brakes, the brake hydraulic pressure (air pressure) gauge must be secure before beginning.
3. When the forklift starts with a tons, the vehicle driver should first validate that the tons is secure and trustworthy.
4. The beginning needs to be slow-moving and steady.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground ought to be kept at 300mm-400mm, and the mast must be slanted in reverse. .
2. Do not lift the fork too expensive when driving. When going into and leaving the job website or while driving, beware that there will certainly be no challenges in the sky. When the tons is taking a trip, the fork needs to not be raised too high, which will influence the security of the forklift. .
3. After unloading, the fork should be lowered to the normal driving position before driving. .
4. When turning, if there are pedestrians or automobiles nearby, the driving signal ought to be issued first. High-speed doglegs are prohibited. High-speed sharp turns will cause the lorry to shed lateral security and tip over. .
5. When the forklift is downhill, it is purely forbidden to shut off the flame and slide, and it is restricted to brake instantly while driving with loads unless there are special situations.
6. When the forklift is running, it should obey the traffic rules in the manufacturing facility and should keep a certain safety distance from the car in front. .
7. When the forklift is running, the lots should remain in the lowest setting that does not prevent the driving, and the gantry should be appropriately tilted back. The tons will not be elevated other than when piling or loading. .
8. The height of the tons should not obstruct the driver's sight. In special scenarios, when the product impacts the forward vision, drive at a low speed when turning around.
9. It is restricted to activate the ramp, neither to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low speed when going into the manufacturing workshop area. .
11. When the forklift is lifted, lifted or driven, it is forbidden for employees to depend on the fork to hold products and play a balancing role. .
12. If problems are located, they will certainly be fixed and reported in a prompt way, and they will certainly never operate with illnesses or hide them.

packing and discharging.
1. When fork-loading products, the range in between both forks must be changed as needed to make the tons of both forks balanced and not skewed, and one side of the product ought to be against the shelf. .
2. It is forbidden to work with a single fork or use a fork top or draw. In special conditions, security indication should be established to remind surrounding pedestrians. .
3. In the process of filling and unloading items, the forklift must be stopped with the brake. .
4. The rate of the automobile ought to be slow-moving and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled items and injure individuals. .
5. When utilizing a fork to fork the goods, the fork must be as deep as feasible under the lots, and it must be noted that the fork pointer ought to not touch various other items or items. The load should be stabilized with very little back tilt of the gantry to ensure that the lots does not slide in reverse. The mast can be tilted forward a little when the tons is decreased to allow for simple positioning of the load and extraction of the forks. .
6. It is restricted to fork goods at broadband and hit hard items with the fork head. .
7. When the forklift is working, it is forbidden for individuals to stand around the fork, so regarding prevent the collapse of the goods and harm people. .
8. Overwhelming is banned, and it is banned to use forks to raise personnel to engage in high-altitude procedures to stay clear of high-altitude dropping crashes. .
9. It is not allowed to make use of the brake inertia to slip, put, round or roll items. .
10. It is not permitted to use forks to choose, transform pallet dump.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Before leaving the forklift, you should dump the goods or reduced the fork frame.
2. Pull the emergency brake take care of to dead or Stand-on Electric Pallet Stacker depress the parking brake switch.
3. The engine is shut off and the power is cut off. (Except for unique conditions, such as the vehicle driver does not leave the vehicle's line of vision and does not surpass 1 min).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be examined, and gas, lubing oil and air conditioning water ought to be added.
2. Inspect the security performance of starting, running and braking.
3. Inspect whether the lights and horn signals are total and efficient.
4. During the operation of the forklift, check whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leak ought to also be checked and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You have to examine prior to leaving the cars and truck;.
2. Stand-on Electric Pallet Stacker When you come across somebody in front of you throughout driving, you must send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The turning need to not be as well sharp to prevent the propensity of " complimentary turning";.
6. Adding and down the slope should be slow-moving and uniform, and no turning on the slope is allowed.
7. Do not drive throughout the gradient. When the slope is greater than 10%, the car ought to be driven in reverse when worsening;.
8. When the forklift workers lug the goods and progress, if they encounter big or hefty products and most likely to the chauffeur's view, they must take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork operation is not enabled.
2. It is not allowed to lift the goods for cross country driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not allowed to use stopping pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to service the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Curves, narrow roads, railway crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the road, the opposite side of the section with the same size as the challenge should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844